Archive for January, 2015

Task Sequence: Image Capture Wizard has failed with the error code (0x00004005)

January 8, 2015 13 comments

While I create Image windows 7 using SCCM, I got error task sequence: Image Capture wizard has failed with the error code (0x00004005)

Process running create image stuck



After some research, I found out there is a maximum 3 time limit to capture image from same computer.

" Each OS capture will run sysprep command which will reset windows product activation. However, there is a max 3 times per computer limit for the sysprep command. After the 3 time, the clock to reset Windows Product Activation can no longer be reset."

To overcome this 3 Sysprep time limitaiton, following are the walkaround:
Open regedit and look for:

Set to value: 2

Set to value: 7


Set to value:

Then, run the command:

msdtc -uninstall (wait a few seconds)
msdtc -install (wait a few seconds)

Then, reboot the system and try to run sysprep again.
It is working to me. Good luck to you. 🙂


Categories: Windows Client

Error Connecting to VPN – Error 850: The Extensible Authentication Protocol type required for authentication

January 8, 2015 2 comments

Hi guys, here I want to share of you, if you will connect to VPN you will get error like picture below, you only check from side client,


here the solution

1. Right Click properties on network that you have set VPN


2. Click Tab Security, choose Allow these Protocol

select challenge handshake…. and Microsoft CHAP…..

Click Ok, and try connect again to VPN


Categories: Windows Client

Error 0x80246008 or 0x80246007 Background Intelligent Transfer Service (BITS) cannot start on Windows XP

January 6, 2015 Leave a comment

1. Reregister the Qmgr.dll and the Qmgrprxy.dll BITS files. To do this, follow these steps:

Click Start, click Run, type regsvr32 qmgr.dll, and then click OK two times.

Click Start, click Run, type regsvr32 qmgrprxy.dll, and then click OK two times.

Restart the computer.

2. Repair BITS. To do this, follow these steps:

Click Start, click Run, type cmd, and then click OK.

a. At the command prompt, type the following command, and then click OK:

%windir%\System32\rundll32.exe setupapi,InstallHinfSection DefaultInstall 132 %windir%\inf\qmgr.inf

Note If you are prompted to insert the operating system CD, type %windir%\ServicePackFiles\i386 in the Copy files from dialog box, and then click OK.

b. Restart the computer.

c. At the command prompt, type the following command, and then click OK:

Reg add HKLM\SYSTEM\CurrentControlSet\Services\BITS\Parameters /v ServiceDll /t REG_EXPAND_SZ /d %indir%\System32\qmgr.dll

d. At the command prompt, type the following command, and then click OK:

Reg add HKLM\SYSTEM\CurrentControlSet\Control\BackupRestore\FilesNotToBackup

e. Restart the computer.

3. Manually start BITS. To do this, follow these steps:

. Click Start, click Run, type services.msc, and then click OK.

a. Double-click Background Intelligent Transfer Service.

b. In the Service status area, click Start.
Note Set the BITS Startup type to "Automatic" instead of "Manual" as soon as BITS starts successfully. To change the Startup type, follow these steps:

1. Click Start, click Run, type services.msc, and then click OK.

2. Double-click Background Intelligent Transfer Service.

3. In the Startup type box, click Automatic, and then click OK.



Categories: Windows Client

Unauthorized: Authorization Failed Lync Control Panel

January 6, 2015 2 comments

hi guys, while I open Lync Control Panel, I get issue Unauthorized : Authorization failed.

The Application cannot verify your credential. Verify your logon credential and contact your support Team. the picture like below


here I think only security member, but after I check I done member csadministrator, and I re login but still unauthorized authenticated. after I check in the event viewer I get some error in the SQL Browser. SQL Browser service was unable to process a client request.


I check the services, actually right the status not started, and I run start and I recheck all services connected with the Microsoft Lync Server 2010, any services not started so I run started



after I open again Microsoft Lync Server control Panel I don’t get issue anymore.


Categories: Lync

Configuring Microsoft Lync use RCC Integrated CUPS (Cisco Unified Presence Server)

January 6, 2015 6 comments

I want to implementation Microsoft Lync Server use RCC (Remote Call Control) integrated with cisco, here I want to share of you how to configure Microsoft Lync integrated Cisco.

I don’t want to discuss configuring in cisco, here I just want to share in side only Microsoft Lync Server 2010 using RCC.

1. The first you must set DNS CUPS (Cisco Unified Presence) so from your server Lync can ping to Cisco Unified Presence. for example this scenario I create name CUPS is


Read more…

Categories: Lync

How to Enable User Lync Base on OU

January 6, 2015 Leave a comment

I have implement in one of Company, and they want to enable user lync base on OU (Organization Unit), but after I click find base On OU I get error

Retrieve :Active Directory User or Contact” Returned Warnings.

Get-CSAdUser: Received a referral to "Jakarta" When requesting "DC=Jakarta" from "". you have specified the wrong server this operation.


but in fact if you want to enable User base on OU you must type with format below

OU=NameOU,DC=DC Name,DC=DC Name

and this is for example to get user base on OU


after that click find


after that block all and Click Ok


and click Enable


and please verify users enabled


Categories: Lync

Configuring Normalization Rule for RCC (Remote Call Control)

January 6, 2015 1 comment

This Scenario from  Remote call Control (RCC), while your desk phone is ringing, Lync Client will pop up telling about your Lync Presence. and if you click Pop up Lync Client the desk phone will answer the call on your desk phone.

but RCC not supported Dial Plan, dial plan only support enterprise voice. but sometime any client must be set to dial plan with any reason one of them is easy user to use Lync RCC.

fortunately, although RCC not supported to dial plan, you can configure with edit Normalization in Company Phone Number Normalization Rules.txt files.

below Step by step :

Copy file Sampe_Company_Phone_Number_Normalization_Rules you can get this file from C:\Program Files\Microsoft Lync Server 2010\Web Components\Address Book Files\Files

copy this file and paste to the share Lync Fileimage

you can get locate share lync file from the topology builder



Read more…

Categories: Lync